A floating vanity looks decisive on a drawing and quietly ambiguous in a catalogue photograph. Wall-hung units combine carcass, countertop, basin interface, hardware and wall fixing in one compact assembly, so a colour that reads correctly on a laminate board can read very differently once the same finish meets a stone top, a concealed bracket and bathroom lighting. Before production starts on a Santerson Floating Vanity, we ask project buyers to approve physical finish samples rather than accept the specification as drawn. This article explains what that sample review covers, what it costs in time, and how the sign-off is recorded so production cannot drift from it.
Why floating vanities need a separate sample round
Every Santerson vanity in the Vanities collection is configurable: finish, layout and dimensions are specified per project, and the floating version adds made-to-measure sizing with wall-mounted support. That configurability is the commercial advantage and the main source of dispute. If the only approved reference is a product page image or a rendered elevation, three parties can each hold a different mental picture of the same unit — the designer's intent, the buyer's expectation, and what the workshop can actually build with the material batch on hand.
A sample round replaces those three pictures with one object. It is also where the questions that matter get answered early: whether a handleless edge detail is achievable in the chosen board, whether a dark matte finish will show water marks in a shared family bathroom, and whether the wall substrate behind the unit can carry the load without additional blocking.
What we send you, and what we need back from you
For a custom furniture project, the sample package is assembled from the specification sheet rather than from whatever is convenient to produce. A typical floating vanity package contains:
- a door or drawer-front piece in the selected finish, large enough to judge sheen and grain direction at arm's length;
- a carcass edge sample showing how the finish wraps the panel edge, since that wrap is where most visual complaints originate;
- a countertop or basin-interface corner showing the actual joint detail, not a schematic of it;
- a hardware sample — pull rail, integrated channel or push-open fitting — mounted on an offcut of the same board;
- the specification sheet itself, with each item numbered so that comments refer to a sample, not to an adjective.
What we need back is equally concrete: which items are approved, which are rejected, and on what grounds. "Not this grey" is unusable; "too warm under 3000 K lighting in the sample room" gives the workshop something to correct. Where a project has multiple bathroom types — guest powder rooms, main ensuites, share-level bathrooms — we prefer one approved reference per finish family rather than one global approval.
The five checks we run on every returned sample
| Check | What to look for | Common failure |
|---|---|---|
| Colour and sheen under site lighting | View the sample in the same colour temperature and brightness as the finished bathroom, not only in daylight. | A matte finish approved in a showroom reads chalky under cool downlights. |
| Grain direction and repeat | Confirm vertical or horizontal grain on every front, and how the pattern aligns across adjacent units in a run. | Wood-effect fronts installed in opposite directions across two vanities in one room. |
| Edge and joint detail | Inspect the wrap, radius and seam where the finish meets the panel edge and where countertop meets basin. | A sharp mitre approved on paper that the chosen material cannot hold at production scale. |
| Hardware behaviour | Open and close the drawer or door sample with the fitting mounted; check finger clearance for handleless fronts. | An integrated pull channel too shallow to grip once the countertop overhang is added. |
| Wall fixing and substrate | Confirm the fixing method against the wall build-up shown on your structural drawings before ordering. | Blockwork that cannot take the bracket load without additional support framed in. |
We do not publish fixed lead times, warranty terms or compliance certificates as standard text. Sample freight timing, wall-fixing requirements and any local certification needed for your jurisdiction are confirmed per project, in writing, against your drawings — because those answers change with the specification and the site.
How the sign-off becomes a production instruction
Once samples come back marked approved, they are logged against the project reference and become the physical benchmark for that order. Production is then checked against the signed sample, not against the original image file. This matters most where several bathrooms repeat the same finish across a villa or a hospitality floor: one approved object keeps forty units consistent in a way that no amount of email description can.
Our cooperation sequence follows three stages — project brief and design proposal, quotation and detail confirmation, then production, shipment and follow-up. The sample review sits inside the second stage, which is deliberate: after it closes, changes to finish or dimension are treated as variations rather than corrections, priced and scheduled accordingly. Buyers who compress this stage usually pay for it later; buyers who run it properly tend to see production move without interruption.
When a floating unit is the wrong choice
We would rather say no at specification stage than build a difficult unit. A wall-hung vanity assumes a substrate that can carry it, clear service runs behind it, and enough floor-to-slab height for the bracket. Where those conditions are missing — older buildings with timber studs, or bathrooms where pipework cannot be relocated — a floor-standing option from the same collection gives the same finish language without the structural argument. Two configurations we specify often in that situation are the Santerson Integrated Countertop Vanity, where countertop and basin are specified as one assembly, and the Santerson Double Vanity for wider ensuites that need two basins on a shared run.
Vanity lighting is specified in the same round, not afterwards. A mirror or sconce above a floating unit changes how its finish reads, so we ask that the lighting choice is at least provisionally fixed before the sample is approved. See vanity lighting for what we currently offer in that category.
A short checklist before you release the order
- Every finish item physically approved and numbered against the project reference.
- Dimensions confirmed on site, including finished wall face — not taken from architectural drawings alone.
- Wall build-up and fixing method agreed with your builder or structural engineer.
- Countertop, basin and tapware interfaces drawn, not assumed.
- Lighting position fixed enough to judge the finish in place.
- Variation terms understood: what counts as a change after sample sign-off.
If you are specifying vanities for a villa or hospitality project and want the sample round handled before production commitments, send us the room drawings and finish direction through the contact page. We will confirm what we can supply in your specification, what needs an alternative, and what the sample package will contain.