A two tone veneer kitchen looks simple on a mood board and complicated on a site drawing. The warmth of real wood on one run of doors, a flat painted or laminated surface on another, and the join between them sitting right where the eye lands. If that combination is going to be manufactured offshore and shipped in crates, the enquiry has to carry more than a colour name and a nice photograph. Below is the input list our production team works from when a Two Tone Veneer Cabinets package moves from drawing to cutting list.

Why two tone veneer kitchens need more input than a single finish

A single-finish kitchen is specified once and repeated. A two tone scheme has at least three separate decisions that all have to be recorded before anyone cuts a panel: which run of cabinetry carries the veneer, which carries the second finish, and how the two meet. Veneer is also the less forgiving of the two. Each sheet has its own grain pattern, so the direction in which doors are cut, and whether they are book-matched or slip-matched, changes the look of a completed wall more than the species itself.

Our built-in furniture range is made to measure rather than offered in fixed modules, and the Wood Veneer Kitchen Cabinets collection — including the two tone version — follows the same rule: finish, layout and dimensions are specified per project. That flexibility only pays off when the measurements and inputs arrive complete.

The measurements that actually decide the build

Send dimensions taken on site, after the finishes that sit against the cabinetry are in place — plasterboard, tiling, screed and flooring. A kitchen drawn from an architectural plan is a starting point; a kitchen built from a surveyed set of room dimensions is what fits.

MeasurementWhat we need recordedWhy it changes the build
Run lengthsEach wall run, measured at three heights (top, middle, bottom), plus out-of-plumb directionTall panels and scribes are cut to the actual wall, not the nominal one
Floor to ceilingFloor-to-soffit and floor-to-ceiling at several points along each runSets whether full-height doors can be used and where a filler is needed
Aperture openingsWindow head and sill heights, reveal depths, door openings and swing directionDetermines where upper cabinets stop and how the two tones break around openings
Appliance scheduleModel numbers or drawings for oven, cooktop, dishwasher, refrigerator, extractor — with clearancesAppliance housings are built to the unit, and the tone split usually runs through this zone
Services set-outPlumbing waste and supply positions, electrical points, gas outlet, power for internal fittingsPanel drilling and cut-outs happen in the factory only if the set-out is fixed before production
Countertop thicknessStone or engineered stone thickness and edge profile, plus splashback detailBase cabinet carcass height and scribe allowance follow the worktop
Island footprintOverall length, depth and height; overhang on each side; kick recess depthIslands are usually where the second tone is introduced, so both faces need the finish called up
Circulation gapsAisle widths between runs and island, plus door swing clearancesDrawer and door hardware choice depends on what can actually open

The project inputs that sit alongside the dimensions

  • Tone map. Label every unit on the layout with its finish: veneer, second colour, or glass. Write it onto the plan rather than describing it in an email, and mark which faces are visible — an island has three or four elevations, not one.
  • Veneer cut and matching. State slip-matched or book-matched, and where a continuous grain run is required across a bank of doors. Grain direction (vertical or horizontal) should be called out per elevation.
  • Sheen. The collection covers matte, dark tone and high gloss wood veneer options. The second finish should be specified at a comparable sheen, or the mismatch will read as a mistake under site lighting.
  • Edge treatment. Door edge profile, radius and whether the veneer wraps the edge or is edged in a contrasting material — this is what makes a two tone detail look intentional at close range.
  • Handle strategy. Handleless profiles, integrated pulls or surface handles. Mixed tones across one run with mixed hardware will fight each other.
  • Internal fit-out. Carcass colour, drawer systems, shelf spans, lighting inside glass-fronted units, and bin or pantry pull-outs.
  • Project context. Villa, apartment or hospitality scheme; quantity of identical kitchens; delivery address or addresses; the trade that carries out installation.
Where a project needs matching veneer elsewhere in the same building — bedroom storage, media walls, pantry and laundry joinery — send those elevations with the kitchen enquiry. The wardrobe side of the range includes Two Tone Veneer Wardrobes in the same Wood Veneer collection, so the two joinery packages can be cut from coordinated material and finished to the same standard.

How the information moves through production

Once the drawings and inputs are with us, the sequence is straightforward. Detail confirmation fixes the cutting list, the veneer sheets are selected against the approved sample so grain and tone match what you signed off, and each unit is factory-finished before packing. Because we work as a one-stop furniture and building materials supplier, the same package can carry the engineered flooring, wall panelling, doors and lighting that sit around the kitchen, which keeps finish matching inside one production and shipping cycle instead of three.

For enquiries where drawings are still at concept stage, our design and coordination service covers space planning, 3D visualisation and production coordination — useful when the tone split has not yet been resolved and you need elevations to make the decision.

A short pre-production checklist

  • Surveyed dimensions, taken after wet trades and flooring are complete
  • Signed elevations with every unit marked for finish
  • Approved veneer sample, cut direction and matching method confirmed in writing
  • Appliance schedule with clearances; services set-out fixed
  • Countertop thickness and edge profile confirmed by the stone supplier
  • Hardware schedule: hinges, slides, handleless profiles, internal fittings
  • Delivery address, access notes and who installs on site

Send what you already have — even a sketch layout with approximate dimensions is enough to start a costing conversation. Complete the inputs above before panels are cut, and the two tone detail that looked difficult on paper arrives on site as drawn.