A full height media wall looks simple on a drawing: panelling from floor to ceiling, a screen in the middle, storage around it. On site it is one of the most coordination-heavy elements in a villa or hotel living room, because the joinery, the screen, the cable routes and the lighting all meet on one face. The difference between a clean installation and a compromised one is usually decided at quotation stage, in the finish details. This guide sets out what buyers should have confirmed in writing before Santerson Full Height Media Walls go into production.

Why finish detail matters more on a full height wall

A low, freestanding unit can absorb small dimensional errors. A floor-to-ceiling composition cannot. Panel joints run through the full storey height, the screen aperture sits at eye level where every misalignment is visible, and the wall usually carries other trades' work — power, data, ventilation grilles, sometimes a fireplace or an electric blind. Because these systems are made to measure for each project rather than supplied in fixed sizes, the specification you send back is what the factory builds. Ambiguity in the finish schedule turns into rework on site.

The Full Height Media Walls listing is configurable: finish, layout and dimensions are specified to suit each space. That flexibility is the point of buying a built-in system, but it also means no two quotations for "the same" wall are comparable unless the finish details are broken down item by item.

1. Surface material and grain direction

Start with what the face material actually is, not the trade name on the drawing. The panel finishes catalogued alongside these walls cover wood veneer, matte lacquer and textured panels, glass and glossy panels, and stone or marble surfaces — Wood Veneer Panels being the most requested for residential media walls. For each of those, confirm:

  • the exact board or panel construction behind the face material, and whether it is suitable for the wall it is fixing to (drywall, masonry, timber stud, or a service cavity);
  • for veneer: species, cut (plain-sawn, quarter-sawn, rift), and whether the grain runs vertically across every panel or book-matches at selected joints;
  • for lacquer and paint: sheen level by area — a satin field with a higher-sheen reveal behaves differently under lighting than one uniform sheen;
  • for stone-look and marble surfaces: whether the face is natural stone or an engineered surface, and how the veining is sequenced across adjacent panels.

Grain direction is the detail most often left out of a purchase order and most often argued about on site. Ask for a marked elevation showing the grain or veining run for every panel, signed off before cutting.

2. Panel jointing, edges and reveals

Decide how the panels meet, in writing, with dimensions. Mitred external corners, shadow-gap reveals, metal trim profiles, or a square butt joint each give a different result and a different price. Confirm:

  • joint type at internal and external corners, and whether mitres are field-touched up after installation or finished in the factory;
  • the width of any shadow gap or reveal, and whether it is consistent between the wall and the ceiling line, skirting and adjacent door openings;
  • edge treatment on visible panel ends, including shelf nosings and the frame around the screen aperture;
  • how the wall resolves at the ceiling — a full height build may need a set-down, a capping, or an allowance for ceiling movement.

3. The screen aperture and what sits behind it

The aperture is where finish decisions have technical consequences. Confirm the screen size and mounting method first — fixed bracket, articulating arm, or recessed into a carcass — because that determines the depth of the pocket and the load path behind the panel. Then confirm:

  • aperture dimensions and the tolerance you are accepting around the screen edge;
  • the material and finish on the inside faces of the aperture, which are visible from an angle and are often quoted as "plain" when they should not be;
  • ventilation route for the screen and any components in the pocket, and whether grille positions are cut in the panel or set into a reveal;
  • access: whether the aperture is serviceable after installation, and whether Sliding Panel TV Systems or concealed doors are used to hide the screen when it is off.

If the design shows a backlit composition, treat the lighting as a separate line item with its own specification — driver location, replaceability, colour temperature and dimming protocol all need naming. Backlit Feature Walls in the same collection are configurable in exactly this way, and electrical details should be confirmed for the specific design rather than assumed from a reference photograph.

4. Storage fronts, hardware and interior finish

Media walls usually combine open shelving with closed storage, and the closed sections carry the hardware that decides how the wall ages. Confirm door and drawer type, handle or handleless detail, hinge and runner make and model, and whether soft-close is included. Then ask what the inside of the cabinetry looks like: interior finish colour, shelf fixing system, exposed cam locks or bare board edges all show up when a door is open in a guest-facing space.

Where the brief needs more storage than the media composition provides, Full Height Storage Walls can be specified to the same finish schedule so the two systems read as one wall. That only works if both are quoted against identical material, edge and hardware schedules — check this before you assume a match.

5. Fixing method, substrate and site sequence

Ask how the wall is intended to be fixed and what condition your site must deliver. Confirm the batten or framing arrangement, whether the substrate needs to be packed and lined flat, where the tolerances for out-of-plumb walls are absorbed, and who carries the risk if the wall behind is not as drawn. Then fix the sequence: wet trades complete, first-fix electrical signed off, then joinery installed, then screen and lighting commissioned. Built-in work installed before those finishes are done is a common cause of damage to the face material.

6. Sampling, shop drawings and handover

For any project where the wall is visible to clients or guests, request a physical finish sample — a real panel offcut in the specified face material and edge detail, not a colour chip from a printed card. Colour and texture read differently under warm residential lighting than on a screen. Then require shop drawings for sign-off before production: set-out dimensions, panel sizes and joint positions, aperture setting-out, cut-out locations for sockets and grilles, and the lighting schedule.

At handover, ask for the documentation that lets the wall be maintained later: hardware model numbers for replacements, driver and dimming details for any integrated lighting, and care instructions for the selected face material. Santerson's service scope covers custom and OEM production, door-to-door logistics, and installation and after-sales support, so these items can be requested as part of the package rather than chased separately.

A short pre-production checklist

  • Face material named by construction, species or type, cut and grain/veining run — with a marked elevation.
  • Joint types, reveal widths and edge treatments dimensioned on drawings.
  • Screen size, mounting method, aperture dimensions, inside-face finish and ventilation route confirmed.
  • Hardware makes and models, soft-close scope, and interior cabinet finish specified.
  • Lighting schedule with driver location, colour temperature and dimming protocol where applicable.
  • Fixing arrangement and required substrate condition agreed, with a defined site sequence.
  • Physical finish sample approved and shop drawings signed before cutting starts.

Work through those seven items and the quotation stops being a picture of a nice wall and becomes something you can actually build to. Send us your elevation, screen size and storey height, and we will price the wall against that finish schedule — including matching storage runs, integrated lighting and delivery to site as part of turnkey interior project solutions.

SANTERSON — furniture and building materials manufacturer, Foshan, China. Phone / WhatsApp: +86-13928214007 (PHILLIP) · Email: santerson@qq.com · Enquiries via santerson.com