A single line on a drawing set - "melamine cabinetry, textured finish" - is enough to start an argument between a designer, a builder and a procurement officer. Textured melamine is one of the most requested surface treatments in residential joinery because it reads warm under light and hides fingerprints, yet it is also one of the easiest specifications to get wrong, because "textured" covers anything from a fine micro-grain to a deep embossed wood pattern.
This guide sets out the measurements and project inputs that let a factory quotation team price textured melamine cabinets correctly the first time - and what happens downstream when each of them is missing.
Why textured melamine needs a different brief than a flat door
Melamine faced panel products are supplied as decorative paper laminated to a substrate, so the cabinet carcase and the door can be specified separately. A textured surface changes how the panel behaves on site: it reflects light directionally, it shows a shadow line at every edge treatment, and it cannot be corrected on site the way a painted door can. That is why our production team asks for more than a front elevation before quoting.
Our melamine kitchen range also sits alongside matching built-in storage - textured melamine wardrobes, two tone melamine cabinets and wood grain melamine cabinets - so the same inputs carry across a whole apartment or villa floor, which is exactly how we prefer to receive enquiries from builders and fit-out contractors.
The measurements that must be on paper before production
Made-to-measure joinery is quoted by module, not by room. Send us the following, taken on site after the floor, wall and ceiling finishes are complete:
| Input | What we need to see | Why it changes the price and the fit |
|---|---|---|
| Overall run lengths | Wall-to-wall length of each run, in millimetres, plus out-of-plumb variance at both ends | Determines filler panels, scribe cuts and whether a square module can be used at all |
| Floor to ceiling height | Finished floor level to soffit, at three points along the run | Sets tall-cabinet heights, top panel size and whether the carcase reaches the ceiling |
| Appliance schedule | Model references with cut-in width, height, depth, door swing and ventilation gap | Appliance housings are fixed before the surrounding modules can be sized |
| Sink, tapware and bench details | Bowl cut-out dimensions, tap hole positions, benchtop thickness and edge profile | Controls rail height under the window, drawer pack layout and benchtop support |
| Services locations | Water inlet, waste, dishwasher drain, power points, rangehood duct, on a dimensioned plan | Decides which modules can host plumbing and where cut-outs are permitted |
| Door and opening clearances | Swing arcs of adjacent doors, plus aisle width for walk-in pantries | Prevents handle and door collisions once the cabinetry is installed |
| Carcase and door thickness | Panels you want for the box, and for the front | Affects hinge choice, concealed hardware and drawer runner depth |
Project inputs that decide finish, layout and cost
1. Where the cabinetry is being installed
A private residence, a short-term rental and a serviced apartment all use the same floor plan but not the same specification. Tell us the occupancy pattern and who cleans the space. High-turnover interiors usually move toward a tighter grain and a more forgiving edge band; owner-occupied villas often allow a deeper texture that reads beautifully at close range.
2. Texture direction and light exposure
Send photographs of the room at the time of day it is used most, and note which elevations face daylight. A strong directional grain on a north-facing run will look different from the same panel in a galley kitchen lit only by under-cabinet lighting. If you want the texture to run vertically or horizontally across a run, say so on the drawing - this has to be instructed at cutting, not discovered at installation.
3. Handle strategy
Handles, integrated pulls or push-open mechanisms each require different clearances between doors and drawers. A handleless detail needs a consistent reveal on every module in the run; if two suppliers are involved, this is where the first visible error appears.
4. Interior configuration per module
Send the internal layout you expect: drawer packs, shelf spacing, pantry racking, cutlery division, appliance towers. We build to your list rather than guessing it, and a written configuration list is what stops a quotation from being revised twice.
5. The rest of the joinery package
Because we also produce interior fixtures and built-in furniture, tell us early whether wardrobes, laundry joinery, TV walls and vanity units should be matched to the same melamine decision. Ordering one coordinated package keeps grain, edge band and hardware consistent across the project.
How the information reaches us
A workable enquiry usually contains a dimensioned plan and elevation set, an appliance schedule, a finish reference, and one named person who can approve shop drawings. If you do not have drawings yet, our design team can start from a brief and produce layout planning, furniture layouts and 3D renderings before anything is cut - see interior design services. For contractors who already have a design and only need manufacturing to their own detail, custom & OEM service covers bespoke material finishes and textures with flexible minimum order quantities.
Once the shop drawings are approved, production is followed by freight and logistics and door-to-door delivery, then on-site guidance at handover. Builders who want a single point of contact for cabinetry alongside flooring, wall panels, doors and lighting generally work with us as a one-stop furniture and building materials supplier rather than coordinating several factories per project.
Before you send an enquiry: confirm that the melamine finish reference you have chosen is intended for the panel type you are buying. The same decorative pattern can be offered on different surface textures, and a sample held against the door in the actual room light is still the fastest way to avoid a costly remake.
Send us your drawings
Share your dimensioned plan, elevation set, appliance schedule and finish reference, and our project team will return a quotation with the module breakdown, hardware list and production schedule for your review. As a China-based furniture and building materials manufacturer, we supply residential and hospitality projects internationally, including villa and apartment work in Australian cities such as Sydney and Melbourne.
Contact our project team to start a quotation.