An L-shaped walk-in wardrobe looks simple on a rendering: two runs of cabinetry meeting in a corner, hanging rails, shelves, drawers. The difficulty shows up later — on site, when the returns do not line up with the slab, when the door leaves foul the adjacent wall, or when the internal fittings arrive in a different configuration from the one the drawing showed. For Australian villa and apartment projects we supply joinery as made-to-measure work, so the verification list below is the same one our own production coordination works from. Use it before you place an order, not after.
Start With What Is Actually Being Made to Measure
Our L Shaped Walk in Wardrobes sit within the Walk-in Wardrobes collection, and the product record states the scope plainly: made-to-measure sizing, material and finish options, and a layout tailored to the project. That wording matters when you compare quotations. "Custom" can mean anything from a full set of shop drawings signed off by your side to a supplier resizing two standard carcasses and calling it bespoke.
Before pricing is agreed, ask the supplier to confirm in writing which of these are inside the quoted scope: shop drawings with overall and internal dimensions for both runs; the corner treatment (angled carcase, blind-corner fitting, or one run terminated into a wall panel); door type and its swing or slide envelope; skirting and cornice cut-outs; and whether the carcass is scribed to an out-of-plaster wall. If any of these are missing from the quotation, they will be variations later.
Verify the Corner Geometry Before Anyone Cuts Board
The corner is where an L layout either works or wastes a metre of storage. Three checks settle it:
- The internal angle. Take the measurement from finished wall face to finished wall face, at three heights, and record the deviation. A corner that is not square changes every downstream dimension, and a supplier working off a single nominal figure will build to the wrong one.
- The return length. Short returns (under roughly 700 mm) cannot take a standard 600 mm deep carcase without eating the walk-through. Confirm whether the short run is shallow storage, a drawer bank, or an open niche.
- Ceiling and service runs. Downlights, air-conditioning returns and bulkheads sit above wardrobe height on most Australian drawings. Send the reflected ceiling plan with the wardrobe dimensions, not afterwards.
Match Internal Zoning to How the Room Will Be Used
Walk-in layouts get specified by appearance and then fail on capacity. Settle the split between long hanging, double hanging, drawer storage and open display before finishes are chosen, because internal fittings drive the module widths. For a project where most of the wardrobe is daily wear, double-hanging sections plus a drawer bank usually serve better than one long rail. If the brief leans toward display — guest villas, boutique-style bedrooms — glass-fronted sections and integrated lighting become part of the layout rather than an add-on; see Glass Walk in Wardrobes for that direction, and U Shaped Walk in Wardrobes when the room allows a third run.
Ask for the internal elevation showing every rail, shelf and drawer at height. A single perspective render hides awkward gaps; elevations do not.
Pin Down Materials and Finish by Name
Our wardrobe range is offered across lacquer, acrylic, melamine, wood veneer and aluminium-framed glass fronts. The finish family is a decision you should record on the order, because "matte grey" means different things in acrylic, lacquer and textured melamine — different sheen levels, different edge treatment, different behaviour around fingerprints and cleaning agents.
For carcasses, confirm the substrate, the thickness, and how the edges are finished. For doors, confirm whether the panel is a single leaf or a framed construction, and what hardware carries the weight. If your project specifies handleless profiling or an aluminium channel, that profile belongs to the door build and should be listed as its own line item.
Decide Who Owns Installation and Snags
Imported joinery usually fails at the handover point rather than in the factory. Our service scope covers production, logistics with door-to-door delivery, installation support and after-sales, but the split of responsibility on an Australian site still needs to be written into the order: who unpacks and stores the panels, who carries out on-site installation, who adjusts doors after the floor finish is laid, and what happens if a panel is damaged in the final phase of works.
Two practical items settle most disputes. First, confirm the delivery address is a site with vehicle access for the container or pallet delivery you are ordering — villa sites in established suburbs often are not. Second, agree the sequence: joinery should be installed after wet trades, floor finishes and painting are complete, with the opening dimensions re-checked on site before production release.
Read the Documentation Against Your Own Drawings
Before payment is released for production, check that the supplier's drawings carry the same numbers as your architectural set. The differences we see most often in wardrobe packages are small and cumulative: a nominal 2400 mm height against a 2365 mm finished ceiling; a door swing shown clear of a wall that has since gained 20 mm of plasterboard; an internal rail position that clashes with a drawer. One reconciliation pass on paper costs nothing. The same correction after shipping does not.
We work from Australian project documentation and produce shop drawings for your sign-off before manufacturing begins — the same sequence used on villa projects in Sydney, Melbourne, Perth and North Turramurra. Send us your layout, and we will return dimensions, finish references and an itemised quotation you can compare line by line against any other supplier.
SANTERSON is a China-based furniture and building materials manufacturer supplying custom joinery and interior fit-out products to residential and hospitality projects. For wardrobe enquiries, send drawings and site dimensions and we will confirm scope, finishes and delivery terms for your project.