A grey shaker cabinet line is easy to specify and hard to schedule. The door profile is familiar, the colour sits quietly against stone and timber, and it works across villa kitchens, apartment units and serviced-apartment blocks. What trips procurement teams up is that cabinetry never arrives alone: appliances, worktops, splashbacks, tapware, lighting and flooring all have to agree with the cabinet dimensions you published on a drawing sheet months earlier.
This article looks at how to put grey shaker cabinets into a whole-project materials schedule, so one decision made in the kitchen carries cleanly through joinery, wet areas, finishes and delivery instead of turning into variation orders later.
Start from one item number, not one product photo
In a materials schedule every line needs an identity that survives from the first tender drawing to the last installation inspection. Give each cabinet run its own item code — for example K-A for the main kitchen wall, K-B for the island, and separate codes for tall storage, pantry and laundry joinery. Then record against each code the door style, the specified finish, the carcass construction, the hardware set and the room it belongs to.
Keep one product reference per item code. A collection such as our grey shaker range covers made-to-measure sizing, material and finish selection and a layout set to the space, so one code can carry a full wall of joinery. Where a design deliberately mixes two looks — say an off-white upper run against a darker base run — split them into separate codes rather than describing both inside a single row.
A schedule row that says only "grey shaker kitchen" cannot be quoted, compared or inspected. A row with an item code, door reference, finish note, hardware set and room location can.
Record the finishes and hardware you actually intend to buy
Grey is not one specification. The same shaker profile can be requested in a painted finish, a matte laminate, an acrylic surface or a wood-veneer grain, and each behaves differently under kitchen lighting and against different worktop edges. Our catalogue lists these as distinct product lines, including painted shaker cabinets, grey matte cabinets and matte acrylic cabinets, so the finish name in your schedule should match the line you are actually specifying.
Write the hardware into the same row: hinge type, drawer runner type, handle or handleless detail, and whether integrated lighting is part of the cabinet. Cabinet-integrated lighting sits with the joinery package, not with the electrical contractor, so a schedule that leaves it out tends to produce two quotations for the same fitting — or none.
Let the cabinet dimensions drive the rest of the schedule
Once the run is drawn, the cabinet sets the numbers everything else must fit. Worktop thickness and edge detail follow the door and carcass build. Splashback height follows the upper-cabinet line. Aperture sizes for built-in ovens, refrigerators and wine cabinets come from the tall and base unit heights. Where a design includes glass display sections or open niches with lighting, as in this light grey shaker kitchen with integrated wine fridge and LED-lit display cabinets, the electrical points have to be set before the carcasses are packed.
Move outward from the kitchen in the same pass. Flooring levels decide the floor-protection detail at cabinet fronts and the height of adjustable feet. Interior doors and architraves need to clear drawer and door swings. Wall panelling, mirror cabinets and vanity units in adjacent rooms should be listed with the same finish logic so the grey palette does not drift from room to room.
Group wet areas, lighting and storage under one schedule structure
Kitchens are where a materials schedule usually starts, but the same rows should carry the rest of the fit-out. For bathroom areas, list sanitary fixtures — wall-hung basins and toilets, vanities, shower sets — against room codes that also record tiling, tanking and the framing needed for concealed cisterns. For living areas, list wardrobes, media walls, shelving and sideboards as joinery items with their own finish references, using the same naming convention you applied in the kitchen.
Lighting deserves its own block but not its own logic. Record pendants over islands and dining tables, ceiling fixtures, wall sconces and cabinet lighting with the fitting reference, the mounting position and the circuit it belongs to. A pendant scheduled above an island is a cabinetry decision as much as a lighting one: the island width, the worktop joint positions and the isolator location all follow from it.
| Schedule block | What the row must carry | Decisions it locks in |
|---|---|---|
| Kitchen joinery | Item code, door style, finish, carcass, hardware, room | Worktop, splashback, appliance apertures, electrical points |
| Built-in appliances | Appliance type, dimensions, ventilation, power | Cabinet heights, isolator positions, service access |
| Bathrooms | Basin, WC, vanity, shower set, room code | Tanking, framing, tiling set-out, waterproofing upstands |
| Floor and wall finishes | Material reference, area, edge and transition detail | Threshold heights, skirting detail, protection to installed joinery |
| Lighting | Fitting reference, position, circuit, dimming | Set-out against cabinetry, ceiling openings, driver access |
Match the schedule to how the package is made and delivered
A materials schedule only helps if it mirrors the way the goods reach site. As a one-stop furniture and building materials supplier, we take the same item codes through design coordination, production and handover: layout drawings and 3D visuals first, then quotations with confirmed details, then manufacturing and quality control, freight and site coordination. That continuity means a row you approve at tender stage is the row that gets produced, packed and inspected — no translation into a second numbering system.
For projects outside China, plan the schedule around container groups rather than rooms alone. Joinery is made to measure, so a container released early has to be the container whose drawings are frozen. Our logistics service covers sea, air and rail freight forwarding, packaging and container loading, customs paperwork such as commercial invoices, packing lists and certificates of origin, shipment tracking and door-to-door delivery. Import terms, duties and transit arrangements differ by project, so confirm them for each consignment rather than assuming one set of terms across the whole job.
Close the loop with site coordination and handover
Add two columns that most schedules leave blank: a status column and an acceptance column. Status tracks whether a row is pending approval, in production, shipped or on site. Acceptance records who signed off the sample and when. For grey shaker cabinets specifically, approve one physical door sample — finish, sheen level, edge profile and handle detail — before releasing the full run, because a grey that reads neutral on a screen can pull warm or cool against real stone.
Our installation and after-sales service covers on-site fitting, inspection and snag lists, warranty coverage, spare parts and ongoing maintenance. For villa and apartment work in Australia, we have delivered projects including Platin Housing Willoughby, Platin Housing Perth, Platin Housing North Turramurra, and villas in Melbourne and Sydney. Installer availability, warranty terms and response arrangements are confirmed per project, so record them against the relevant item codes rather than as a general note.
A short checklist before you release the schedule
- Every cabinet run has its own item code, door reference and finish name that matches an actual catalogue line.
- Appliances, integrated lighting and hardware are listed inside the joinery rows, not in separate trades.
- Worktop, splashback, tiling and flooring rows carry the dimensions set by the cabinetry drawings.
- One approved physical sample is recorded for the grey finish before production release.
- Container groupings follow drawing freeze dates, not room order.
- Status and acceptance columns are filled in at every stage through to handover.
If you are assembling a kitchen, bathroom and joinery package for a villa, apartment or hospitality project, send us your schedule and drawings. We will check the item codes against what can be made, flag anything that would need a separate trade, and quote the package as one coordinated set of interior fixtures and finishes.
Talk to PHILLIP about your project schedule — Phone / WhatsApp: +86-13928214007 · Email: santerson@qq.com · Contact page