A swim spa that looks right on a mood board can still fail on site if the drawings and the ground conditions are never reconciled. The Outdoor Swim Spa WS-PC07ST is a 7-metre configurable model in our swimming pools and swim spas range, combining a swim training station with a hydrotherapy seating area. That combination makes it popular for villas and small resort settings, and it also means the coordination work has to cover structure, services and access at the same time. The notes below follow the order we use on real projects: confirm the envelope, fix the support condition, plan the services, then lock the sequence before anything is shipped.

Start from the envelope, not the brochure

The first drawing set for a project usually shows the spa as a simple rectangle on a terrace or in a garden room. Before that rectangle becomes a dimensioned plan, ask what the shell actually measures and how much working space sits around it. The catalog specification for this model lists an outer shell of 7000 × 2400 × 1470 mm, with cabinet, steps, plant access and any perimeter decking adding to that footprint. A plan that only draws the water area will understate the excavation, the deck framing and the delivery route.

Three envelope items need a decision before the design is issued:

  • Installation style. Above ground on a slab or deck, semi-recessed, or fully recessed with the rim level with the finished floor. Recessed work changes the excavation, waterproofing and drainage scope, so it should appear in the same drawing revision as the spa itself.
  • Cover clearance. This model can be specified with an automatic cover option. A cover mechanism needs clear space to travel and to stack; a hand-drawn plan rarely shows that swing zone until the builder asks for it.
  • Access and egress. Steps, handrails and the shallow seating area all sit outside the nominal shell dimension. Confirm which side they land on against the landscape layout, not after the paving is set out.

Reading the specification into the drawings

Once the envelope is agreed, the product specification becomes a checklist for the services engineers. Here is what the captured catalog data for WS-PC07ST shows, and what each line means on paper:

Catalog itemShown valueWhere it belongs in the drawing set
Shell dimensions7000 × 2400 × 1470 mmArchitectural plan and section; setting-out dimensions for the base slab
Swim training system1 setPositioning of the swim end, plus clear swimming length in the landscape layout
Jets6 pcsSeating-zone layout and user circulation around the hydrotherapy area
LED lights4Low-voltage lighting circuit and any external lighting scheme
Filter pump1 pcPlant access, maintenance reach and noise separation from neighbours
Control system1 setLocation of the user interface and its sightline from the deck
Total power6.55 kWElectrical schedule, cable route, isolation point and protective device sizing

Two lines in that table need a written confirmation rather than an assumption. The water pump is not listed for this model in the captured specifications, so whether one is included depends on the configuration chosen. And while ozone appears as a feature of the range, the options list — control systems, UV sterilisation, water pumps, heat pumps, sand filtration, insulation and steps — varies by model and by project. Put the agreed option list in the specification document itself, with each item marked included, optional or excluded, so that nobody prices or installs from a brochure image.

Practical rule: every number above is a catalog figure for this model. Treat it as the starting point for coordination and re-confirm the final equipment list and electrical requirements against the configuration you order. That single step prevents most on-site surprises with swim spa installations.

Site requirements to close out before production

The following items are the ones that typically hold a project up if they are left open. Each should have a named party and a drawing reference attached in the coordination minutes:

  • Structural support. A full shell of this size carries a substantial loaded weight once filled. The slab or deck structure needs an engineer's sign-off for the finished load, including the rim detail where the spa meets paving or decking.
  • Power supply. With total catalog power shown as 6.55 kW, the electrical design must cover supply capacity, dedicated circuit, isolator location and bonding to match local installation rules. Confirm the required supply arrangement for the selected configuration before the first fix.
  • Drainage and overflow. Recessed installations in particular need an agreed drainage route, overflow arrangement and space for any sand filtration option.
  • Delivery path. A 7-metre shell needs a clear route from the delivery vehicle to the foundation. Check gates, overhead lines, garden walls and any crane lift against the site plan early — this is where villa sites in tight suburban lots usually lose time.
  • Insulation and heating choice. Insulation and heat pump options change both the running set-up and the plant space. Decide them at design stage, not after the shell arrives.

How our project team handles the coordination

Because a swim spa sits at the boundary between landscape architecture, structure and building services, it fits naturally into a coordinated package rather than a single product order. As a one-stop furniture and building materials supplier, we handle the spa together with the surrounding outdoor fit-out — paving-adjacent furniture, pergolas, loungers and screens — so that one drawing set governs everything.

The coordination follows the stages described on our interior design services page: space layout planning and product specification at brief stage, quotation and detail confirmation once the option list is fixed, then production, shipment and follow-up. Where a project needs non-standard dimensions, finishes or an alternative configuration in the range, our custom and OEM service covers design and prototyping before manufacture. Freight, documentation and door-to-door delivery are arranged as part of the same package, with installation support and after-sales follow-up after handover.

Related models in the same range

If 7000 mm is too long for the site, or if the swim end is not required, two neighbouring configurations solve the same brief with a smaller envelope. Outdoor Swim Spa WS-PC05ST keeps the swim training system in a 5000 × 2400 × 1470 mm shell, suited to narrow terraces and courtyard villas. Outdoor Swim Spa WS-PC08ST extends the same layout to 8000 × 2400 × 1470 mm for larger resort and estate settings. Comparing them at drawing stage — not after the landscape contractor has set out the paving — keeps the base slab, drainage and electrical routes reusable across options.

If you are coordinating a villa or small hospitality project and have a layout drawing ready, send it over with the intended installation style. We will confirm which configuration suits the envelope, mark up the services requirements against your drawings, and return a specification you can issue to the builder.