A wardrobe line that looks right on a drawing can still fail on site if the specification behind it is vague. For built-in joinery, the difference between a smooth handover and an expensive rework usually comes down to how precisely the panel detail, sizing basis, material schedule and interior layout are recorded before production starts. The shaker panel wardrobe in our Classic Paneled Wardrobes collection is a good example of why: the profile reads as a simple recessed field inside a square frame, yet every part of that profile has to be defined on paper before a single board is cut.
What makes a specification clear rather than decorative
A clear specification answers four questions without leaving any of them open: what the door leaf actually looks like in section, how the unit is measured and fitted to the opening, what material and finish each surface is made from, and how the interior is organised. A document that only carries a photograph and a colour name answers none of them.
Within the paneled family, this line sits alongside raised, recessed, arched and glass-fronted variations. The shared trait is a framed door leaf; what changes between them is the profile of the field and the edge treatment. Naming the family alone is therefore not enough on a purchase order — the specific door style has to be identified.
The six fields every wardrobe specification needs
| Field | What to record | Why it matters on site |
|---|---|---|
| Door profile | Framed leaf with a recessed centre field; square inside corners and flat rail/stile faces unless a detail drawing says otherwise. | Moulding direction, shadow lines and hardware reveal all follow from the profile. |
| Sizing basis | Whether dimensions are nominal or site-adjusted, and who signs off the final opening sizes. | Built-in units are made to the finished opening, including floor, ceiling and wall finishes. |
| Material and finish schedule | Substrate for carcass and door leaf, edge treatment, paint or veneer system, sheen level, interior lining. | Sheen and colour under project lighting are the most common source of disputes at handover. |
| Interior layout | Hanging heights, shelf spans, drawer banks, mirrors, lighting provisions and any soft-close fittings. | Interior parts are cut to the same drawing; late changes mean remade components. |
| Interface details | Skirting treatment, scribe and filler widths, door swing clearance, adjacent wall and floor materials. | These decide whether the unit sits flush against a finished room. |
| Approval record | Drawing revision number, sample reference, date and approver for each decision. | An untracked verbal change is the fastest way to produce the wrong door. |
Santerson shaker panel wardrobe is made to measure, with material and finish options and a layout tailored to each project. Dimensions and selected specifications are confirmed per project, so the specification document is the control point for all of them.
Reading the panel detail correctly
The shaker profile is often described as "simple", which leads buyers to skip it in the paperwork. It should still be drawn in section: the width of the stile and rail, the depth of the recess, whether the field is a single flat panel or carries a secondary moulding, and how the frame meets the carcass front. Two doors can both be called shaker and look completely different once those numbers change.
Where a project needs a softer or more decorative line, the same collection lists Raised Panel Wardrobes, Recessed Panel Wardrobes and Arched Paneled Wardrobes. Comparing them against one drawing, rather than against catalogue photos, keeps the decision on measurable geometry instead of impression.
Choosing the door material and finish schedule
Paneled doors are available across different substrate and surface systems, and the choice affects both cost and how the door behaves over time. Solid timber frames with panel infill behave differently from engineered boards with a laminate or lacquer surface, particularly at edges and in humid rooms. Record the system by name for each surface — door face, door reverse, carcass exterior, carcass interior — instead of writing one finish for the whole unit.
For projects that need a specific colour, request a physical sample against the drawing revision you are working from. A paint or veneer sample approved at concept stage is worthless if the drawing has since changed and nobody re-approved it.
Interior layout: decide before production, not at handover
- Set hanging zones by garment type, and keep shelf spans within the span the chosen shelf material can carry without a centre support.
- Place drawer banks where they clear the door swing; a drawer that hits an open door is a layout error, not an installation error.
- Decide now whether interior lighting, mirrors or a vanity surface are in scope, because they need wiring and cut-outs in the same production run.
- Note anything that has to be specified separately — custom minimalist bedroom wardrobe layouts, walk-in areas, corner units or laundry integration usually involve their own components and trades.
Our interior design service covers space layout planning, concept design, furniture layouts with 3D renderings, and project design coordination including drawings, production coordination and on-site guidance. Using that coordination stage to freeze the interior layout is usually cheaper than resolving it during installation.
How a one-stop supplier changes the paperwork
When wardrobes, cabinetry, doors, wall panelling and flooring come from separate suppliers, each party specifies to its own drawing set and the interfaces fall between them. Consolidating built-in joinery with interior fixtures through a single one-stop solution means one drawing set carries the interfaces, and one production schedule carries the components that have to arrive together.
For buyers working from overseas, our logistics and door-to-door delivery service covers freight forwarding by sea, air and rail, customs paperwork, packaging and container loading, shipment tracking and door-to-door delivery. Import terms, duties, insurance, transit time and delivery scope are confirmed case by case for each destination, so those commercial details belong in the same specification file as the joinery drawings — not in a later email exchange.
The custom and OEM service covers bespoke finishes and textures, prototyping, material choices including wood, metals, engineered stone and laminates, and flexible minimum order quantities. That flexibility only helps if the specification already states what is required; it is not a substitute for a defined brief.
Pre-production checklist
- Door profile drawn in section, with stile and rail widths and recess depth stated.
- Final opening dimensions signed off against finished floor, wall and ceiling levels.
- Material and finish schedule written per surface, with sheen level named.
- Colour or veneer sample approved against the current drawing revision.
- Interior layout fixed, including fittings, lighting provisions and clearances.
- Interface details resolved: skirting, scribes, door swing, adjacent materials.
- Packaging, delivery sequence and installation responsibility confirmed in writing.
Send us the opening dimensions, the drawing revision and the finish you are working to, and we will return a specification for your shaker panel wardrobe with the profile, material schedule and interior layout set out line by line — so approval happens on paper before production begins. As a China-based furniture and building materials manufacturer, we handle built-in joinery alongside the rest of the fit-out under one coordination process.
Talk to PHILLIP — Phone / WhatsApp +86-13928214007 · Email santerson@qq.com. The contact page states enquiries receive a response within 24 hours, Monday to Saturday, 8:00 AM–6:00 PM (GMT+8).