Project buyers usually start looking at swim spas for one of two reasons: a villa or resort site has an outdoor area that cannot take a full in-ground pool, or the client wants hydrotherapy and relaxation in the same compact footprint. Both questions have a practical answer, and it is mostly about timing. A custom outdoor swim spa such as the model Outdoor Swim Spa WS-S07M sits in our configurable outdoor swim and hydrotherapy range, and the moment it enters a project schedule determines how much of the specification stays under your control.

Signals that point to a custom-configured swim spa

A standard catalogue unit works well when the site can accept the published shell and the plant layout as it is. A custom conversation becomes worthwhile when one of these conditions appears in your brief:

  • The plot will not take a full pool. A swim spa shell needs a much smaller footprint than a lap pool, and it can sit on a terrace, deck or paved courtyard instead of being excavated.
  • The client wants exercise and recovery in one fixture. When the same outdoor area has to serve daily swimming and jet-based relaxation, a combined swim and hydrotherapy layout avoids two separate installations on the same terrace.
  • Non-standard shapes are on the drawing. Curved terraces, internal courtyards and irregular setbacks often need a bespoke shell geometry rather than a rectangular catalogue mould.
  • The specification is not settled at tender stage. Catalogue options for this range include control systems, UV sterilisation, additional water pumps, heat pumps, sand filtration, insulation and steps. Availability and compatibility vary by model, so the configuration has to be fixed before production starts.
  • You are already sourcing other fit-out items from one supplier. Where outdoor furniture, wall panels, flooring, bathroom fixtures and lighting are being consolidated, adding the water feature to the same procurement package reduces interface risk between trades.

What the WS-S07M catalogue sheet actually gives you

The published sheet for this model lists a shell of 7000 × 2200 × 1480 mm, one control system, three water pumps, one filter pump, forty jets in total, two LED lights and a total power figure of 10.75 kW. The features shown on the page are water jets, LED lighting, ozone, a waterfall and four water columns. Treat every one of those lines as catalogue data for this configuration: they are the starting point for a specification, not a promise about the unit that arrives on site.

Two points matter for a procurement file. First, the captured specification for this model does not list a swim training system, so if your client's brief depends on a counter-current swimming station, raise that with us and confirm it in writing before you commit to the drawing. Second, total power is a catalogue figure for a configuration, not an electrical design. Your engineer should size supply, protection and earthing from the equipment list of the final specification rather than from any single number on a product page.

Where the 7000 mm shell does not fit, adjacent models in the same range show different dimensions and jet counts — for example Outdoor Swim Spa WS-S06M at 5900 × 2200 × 1610 mm, and Outdoor Swim Spa WS-S08M at 8020 × 2260 × 1280 mm. Comparing the published sheets side by side is a quick way to see whether length or depth is the binding constraint on your site, and it gives you a shortlist to send us.

When shape flexibility matters more than model choice

Some sites simply do not fit a rectangular shell, and some clients want a circular or curved feature as the focus of the outdoor design. For those cases our Customizable Shape Outdoor Spa covers square, round, oval and curved geometries on an acrylic shell with structural reinforcement, which is the route we take when architecture, rather than equipment, drives the design. If your project needs that kind of form study, send us the terrace plan early and we will work from the drawing instead of the catalogue.

When a standard catalogue unit is the better call

Not every project needs a bespoke conversation. Where a rectangular shell of roughly seven metres by 2.2 m fits the terrace, where the client is content with the published jet and water-feature layout plus catalogue options, and where the site date leaves room for standard production, ordering from the range as published is usually the faster and lower-risk route. The signals list above is there to help you tell those two situations apart early, rather than discovering a mismatch after the drawings have been issued.

Where to raise this in the project schedule

The single most useful thing a buyer can do is bring the swim spa into the programme at concept or design-development stage, not at order stage. Three reasons:

  • Structures and services follow it. Deck loading, waterproofing, drainage, plant location and power routing all depend on the shell you settle on. Locking the spa late forces those trades to redesign around it.
  • Options change the build. Heat pumps, insulation and sand filtration are not cosmetic add-ons; they affect plant space and electrical load, so they should be decided while coordination drawings are still open.
  • Freight is planned, not improvised. Our logistics and door-to-door delivery service covers freight forwarding by sea, air and rail together with customs paperwork, packaging and container loading. A large shell needs its transport route and site access agreed in advance, alongside the rest of your one-stop furniture and building materials package.

For villa and hospitality projects where we also coordinate interior design, the water feature is easiest to place while layout drawings are still moving. That way it becomes part of the outdoor living scheme rather than an item dropped onto finished landscaping.

What to send us when you enquire

A short, complete enquiry gets a usable quotation back faster. Include:

  • Site plan or terrace layout with the intended spa position and clear access route for delivery.
  • Your target shell length and depth range, plus whether a waterfall, water columns or extra jets are wanted.
  • Local electrical supply details — phase, voltage and available capacity at the plant location.
  • Which options you expect: heat pump, insulation, UV sterilisation, sand filtration, steps.
  • Delivery address, Incoterms preference and required site date.
  • Whether the spa is part of a wider furnishing or fit-out package.

A short checklist before you commit

Confirm the equipment list and electrical requirements for the exact configuration you are buying, not for the range in general. Confirm which items are included as standard and which are options priced separately. Confirm production lead time and shipping terms in writing against your required site date. And confirm who handles siting, connection and commissioning on your side, so no task sits unassigned between trades.

If you are weighing up a customised outdoor swim spa for a villa, resort or hospitality project, send the site plan and target dimensions and we will come back with a configuration proposal against the swimming pools and swim spas range.