A wall-hung bidet looks simple on a product page, but it is one of the bathroom fixtures that punishes poor planning. The bowl has to sit at the right height, connect to both water supply and waste, and carry its own weight on a wall that was not always built for it. The Wall Hung Bidet 1004F, a modern ceramic wall-mount bidet used in home, villa and boutique hotel bathrooms, is no exception. Getting it on site at the right moment, with the wall, rough-in and site team all aligned, is what separates a clean installation from a rework order. The steps below follow how we run this on real projects: one confirmation round before production, then a delivery sequence that matches the site programme.

Start with the wall, not the bowl

The 1004F is fixed to the wall through its back panel, which leaves the floor beneath it clear and gives the bathroom that floating, easy-to-mop look buyers choose wall-hungware for. Before any order goes into the programme, the wall build-up behind the fixture needs to be settled. Timber stud partitions, masonry and steel-frame systems take a wall-hung fixture very differently, and the fixing method follows from that decision, not the other way round. On a renovation this is usually a five-minute site check; on new build it is a drawing that has to exist before the partition is closed.

Two practical points to settle at the same time. First, height: bidets are normally set lower than a wall-hung toilet, and once the waste outlet position is fixed in the wall it is expensive to move. Second, clearances, because a bidet needs elbow room either side, and that space is often eaten by the neighbouring WC or a shower screen once the layout is tightened. We ask project teams to send us the bathroom layout with the fixture heights marked, and we confirm against the technical sheet for the 1004F before we schedule production. If the plumbing rough-in is already on site, we check it against the same sheet and flag any clash before the ceramic ships, rather than after.

Match the suite before you schedule the shipment

Ceramic batches age differently, and a mismatched glaze across a bathroom set is the kind of detail a client notices the day of handover. The 1004F is designed to be combined with a matched wall-hung toilet and basins from the same range so that the whole set reads as one piece. That is a procurement decision, not just a design one: if the bidet is ordered as a lone line item and the rest of the set is bought later, the glaze, the edge profile and the delivery date can all drift apart.

Our approach is to group bathroom sanitary ware into one purchase package under one Turnkey Interior Project Solution, with the bidets, WCs and basins released from the same production run and shipped together. For a villa or a boutique hotel, that also means the spares (the same model, in case of on-site damage or a late room addition) travel in the same container, so there is no second shipment chasing the first one.

Plan the delivery sequence around the wet-trade programme

Ceramics are the last thing you want in a bathroom before the trades have finished. Our logistics team handles sea, air and rail freight with customs paperwork, packing and container loading, and delivers door-to-door, but the delivery date is agreed against the site programme rather than the production date. The working rule we apply on bathroom packages:

• Rough-in stage. Wall frames, water supply and waste outlets for the bidet position are set and verified against the technical sheet. Nothing ceramic has left the factory yet.
• First-fix sign-off. Pressure test on the supply line, waste fall checked, finished wall levels and tile setting-out confirmed. Once these are signed off, the fixture order is released.
• Goods arrive after tiling and ceilings. Ceramic, chrome and mirror-type items are kept in storage until the messy work is complete. Crated fixtures sitting in an active site get chipped, and replacement ceramic rarely arrives in the same batch.
• Final stage, with the other sanitary items. Bidets, WCs and basins are installed in one visit by the same operative, so heights, outlets and sealants are consistent across the set.

For projects outside China we plan transit time and clearance into this sequence rather than hoping for it. A container that lands weeks early ends up in a rent-paid warehouse; one that lands late stalls the wet trades. We build the float into the order date, and we share the tracking milestones with the site contact so nobody is surprised by a container arriving on a Friday afternoon.

Fixing, inspection and handover

Wall-hungware installation is where the planning pays off. The back-panel fixing of the 1004F needs a competent operative, the correct anchors for the actual wall build-up, and a water and waste connection that is tested before the fixture is closed in. On our Furniture Installation and After-sales Support service, the same sequence applies to sanitary ware: set and level the fixture, connect, run the supply and check every joint for leakage, then walk the room with the client and record any snags before handover.

For hotel and multi-unit work this is where a batch approach saves time. If ten bathrooms take the same bidet, one mock-up room should be installed and signed off first (height, clearances, tap reach, how the floor gets mopped underneath) and then repeated across the remaining rooms against that reference. It catches the small decisions that would otherwise be argued room by room.

What to send us before an order is scheduled

A short, accurate brief stops most of the problems above. For a wall-hung bidet package we ask for:

• The finished floor level and the intended fixture height, plus the partition type behind the bidet position.
• Waste and supply outlet positions from the plumbing drawings, or a photo and measurement if the rough-in is already on site.
• The full bathroom set required, so the bidet can be produced and shipped with the matching WC and basins.
• Quantity, spares, delivery location and the date the wet trades finish, since that date drives everything else.

Send those details with your enquiry and we come back with a specification check against the 1004F technical sheet, a production and shipping window that fits your programme, and a delivery plan that puts the ceramic on site when the bathroom is actually ready for it. If you would like that review for a bathroom package on a villa, hotel or residential project, contact our project team and we will work through the drawings with you before anything goes into production.