An integrated basin sits flush with its countertop, so the bowl, rim and surface read as one piece. That clean look is easy to love on a sample board and much harder to deliver when the counter, vanity carcass, taps, mirror and wall finishes are all ordered from different suppliers. A coordinated fit-out package removes most of that friction: one team dimensions the basin, the countertop, the joinery and the surrounding finishes together, then builds and ships them against the same drawings.

What an integrated basin actually requires on site

With an undermount bowl the cut-out must match the basin flange; with a basin moulded from the same slab as the counter, the fall to the waste, the tap deck and the front edge profile all belong to one fabrication. None of these decisions can be made after the countertop template is taken. Before any panel is cut, you need to know the waste position, the tap hole layout, the drawer fronts below, the position of the mirror cabinet above and the finish of the wall behind. That is why an integrated basin works best as part of a package rather than as a single line item on a purchase order.

Our integrated basin is made to measure, so sizing, layout, material and finish are specified per project rather than picked from a fixed catalogue width. The same rule applies to the pieces it has to meet: the undermount basin is confirmed for cut-out and countertop compatibility, and the stone and marble surfaces in the same Countertops & Basins range are fabricated to the project dimensions. Ordering them together means one set of measurements governs the whole vanity run.

The pieces that decide whether the bathroom looks finished

A vanity is judged by its junctions: counter to wall, basin to tap, mirror to light, carcass to floor. Specifying these as one group keeps the timber tones, metal finishes and stone colours consistent, and it keeps the technical details consistent too.

• Carcass and layout. Floating vanities and double vanities are made to measure, so drawer heights, plinth details and wall clearances can be set around the basin instead of adjusted on site.
• One-piece vanity top. An integrated countertop vanity combines the top and the basin in a single specification, which removes the coordination between two fabricators.
• Storage and mirror. The LED mirror cabinet is configured to the project, and its lighting and electrical details are confirmed before the wall is closed up.
• Lighting and small ironmongery. Vanity lighting, towel rails and decorative fixtures are matched to the tap and hardware finish in the same schedule.
• Wet areas and storage. Shower sets, niche shelving, tall linen cabinets and concealed storage come from the same package, so profiles and finishes carry through from the basin to the shower wall.

Where the same project also includes kitchens and other joinery, the fit-out logic extends naturally. Custom built-in kitchen cabinets are built with panel, finish and hardware choices confirmed up front, which is exactly the discipline a bathroom package needs: dimensions and finishes fixed on drawings, then produced in one run.

How a single-supplier package is assembled

SANTERSON is a China-based furniture and building materials manufacturer and one-stop supplier, working on villa, hospitality and office projects from design through to installation. For a bathroom package that carries an integrated basin, the sequence is straightforward:

1. Brief and space planning. Layout, room sizes and how many people use the basin decide the vanity length, basin depth and storage mix.
2. Material and finish selection. Stone or surface material, door finish, tap and hardware tone, and wall finish are chosen together, so samples are compared as a set.
3. Specification and production. Made-to-measure vanities, tops, basins, mirror cabinets and tall cabinets are built to the confirmed drawings, with the technical information for each configuration signed off before manufacture.
4. Logistics. Freight by sea, air or rail is arranged with the packing and documentation for the shipment, and the heavier stone elements are packed with the joinery in mind.
5. Installation and handover. On-site fitting, inspection of junctions and snags, then support for spare parts and maintenance after handover.

Because furniture, joinery and finishes come from one manufacturer, changes travel through the whole package. Moving a waste 80 mm, changing a tap deck, or switching a counter material is re-checked against the carcass, the mirror cabinet and the wall finish in one revision, not in five separate supplier emails.

Details to confirm before the order is placed

• Final room dimensions, and the set-out drawings for the vanity, mirror and lighting.
• Basin type and its waste and overflow position, tap hole layout, and counter thickness at the rim.
• Stone or surface material, edge profile, fall to waste, and how the finish is maintained.
• For LED mirrors and vanity lights: the electrical specification and where the feed is concealed.
• For floating vanities: the fixing method and the substrate it is fixed to, confirmed with the local trade.
• Import terms, duties and Incoterms for the destination country, confirmed case by case for your shipment.
• Warranty scope, spare parts availability and the installation schedule agreed before dispatch.

Plumbing connections, water sealing and any local code requirements stay with the local licensed trades on your project; our role is to supply components to confirmed dimensions and finishes and to coordinate the specification, production, delivery and fitting sequence with your team.

A worked example of the sequencing

Take a villa main bathroom with a long double vanity under a mirrored wall. In a split-supply model, the counter fabricator, the vanity supplier and the glazier each work from their own interpretation of the same drawing, and the mirror ends up off-centre by a few centimetres while the tap holes sit over a drawer. Packaged the same room, we set the basin positions first, then dimension the carcass and drawers around them, mark the tap deck, size the mirror cabinet to the mirror line, and place the vanity light above the glass. The wall finish is decided at the same meeting, so the reveal where the counter meets the wall is detailed rather than patched on site.

This is how our turnkey work is normally run: consultation, design and planning, production, logistics, installation and after-sales. The bathroom is simply one corner of a whole-project package that also covers flooring, wall panels, ceilings, doors, lighting and loose furniture, all specified once.

Frequently asked questions

Can an integrated basin be made for a non-standard vanity length?

Yes. Sizing, layout, material and finish are specified per project, so a basin and counter can be fabricated for the length your room allows. Confirm the final dimensions and selected specification before production starts.

Do you supply the basin with the vanity carcass and the mirror cabinet?

They can be supplied as one package: carcass and top, basin, mirror cabinet, lighting and storage cabinets are all configured to the same drawings and finishes, and can be combined with cabinetry and other joinery for the rest of the project.

Who handles installation?

We coordinate on-site installation, inspection and snags, and provide spare parts and maintenance support after handover. Licensed plumbing and waterproofing work is carried out by your local trades to the requirements of your site.

If you are putting together bathrooms for a villa, apartment or hospitality project, send us the drawings and finish schedule and we will quote the integrated basins, vanities, tops, mirror cabinets and matching joinery as one package at santerson@qq.com or on WhatsApp +86-13928214007.